How to add and reset IKEA products on Hubitat Elevation hub
Authored by: Support.com Tech Pro Team
1. Introduction
How to add and reset IKEA products on Hubitat Elevation hub
2. Resolution
IKEA SYMFONISK
Brand
Device
Product Number
Device Type
Protocol
IKEA SYMFONISK
Sound Remote
20370482
Button Controller
Zigbee
Factory Reset
Remove the battery cover from the bottom of the remote and hold the button for 10 seconds to factory reset.
Wait for at least 10 seconds after reset is complete before attempting to pair the remote.
Join the Zigbee Network
From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
Remove the battery cover from the bottom of the remote and hold the button for 10 seconds.
Save the device and without deleting it from the hub, repeat steps 1 and 2 above.
The hub will report that it found the previously paired device.
If you do not pair a second time with the device already in the Hubitat Elevationâ„¢ database, the remote may not work properly.
Leaving the Zigbee Network
From the device's details page, select Remove Device, then Remove
Remove the battery cover from the bottom of the remote and hold the button for 10 seconds to factory reset.
IKEA TRÃ…DFRI
Device
Product Number
Device Type
Protocol
Warm White Bulb
Bulb
Zigbee
Factory Reset
Cycle power 6 times. The bulb will begin to dim and finally flash one time to indicate that it has been successfully reset.
Wait for at least 10 seconds after reset is complete before attempting to pair the bulb.
Join the Zigbee Network
From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
Cycle power 6 times. The bulb will begin to dim and finally flash 1 time to indicate that it has successfully joined the Zigbee network.
Leaving the Zigbee Network
From the device's details page, select Remove Device, then Remove
Cycle power 6 times. The bulb will begin to dim and finally flash one time to indicate that it has been successfully reset.
Wait for at least 10 seconds after reset is complete before attempting to pair the bulb again.
Device
Product Number
Device Type
Protocol
Outlet
Outlet
Zigbee
Factory Reset
Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
Press and hold the paperclip in the hole for at least 5 seconds (you will feel the paperclip depressing a tiny button inside the outlet).
The LED will pulse quickly and then pulse slowly when you release the internal button.
Wait for at least 10 seconds after reset is complete before attempting to pair the device.
Join the Zigbee Network
From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
Press and hold the paperclip in the hole for 2-4 seconds (you will feel the paperclip depressing a tiny button inside the outlet).
The LED will pulse slowly when pairing and will be steady when pairing has been successfully completed.
Leaving the Zigbee Network
From the device's details page, select Remove Device, then Remove
Using a straightened paperclip, insert it into the small hole on the left side of the outlet next to the LED.
Press and hold the paperclip in the hole for at least 5 seconds (you will feel the paperclip depressing a tiny button inside the outlet).
The LED will pulse quickly and then pulse slowly when you release the internal button.
Wait for at least 10 seconds after reset is complete before attempting to pair the device again.
Device
Product Number
Device Type
Protocol
Signal Repeater
Repeater
Zigbee
Factory Reset
Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
Press and hold the paperclip in the hole for at least 5 seconds (you will feel the paperclip depressing a tiny button inside the repeater).
An LED will pulse quickly and then pulse slowly when you release the internal button.
Wait for at least 10 seconds after reset is complete before attempting to pair the device.
Join the Zigbee Network
From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
Press and hold the paperclip in the hole for 2-4 seconds (you will feel the paperclip depressing a tiny button inside the repeater).
The LED will pulse slowly when pairing and will be steady when pairing has been successfully completed.
The signal repeater will pair as Device. No driver will be assigned and it is not necessary to have one since this device only repeats Zigbee radio signals.
Leaving the Zigbee Network
From the device's details page, select Remove Device, then Remove
Using a straightened paperclip, insert it into the small hole at the end of the repeater next to the USB port.
Press and hold the paperclip in the hole for at least 5 seconds (you will feel the paperclip depressing a tiny button inside the repeater).
The LED will pulse quickly and then pulse slowly when you release the internal button.
Wait for at least 10 seconds after reset is complete before attempting to pair the device again.
.png)
