How to add and reset Linear products on Hubitat Elevation hub

Authored by: Support.com Tech Pro Team

1. Introduction

How to add and reset Linear products on Hubitat Elevation hub

2. Resolution

Factory Reset

1. Factory reset is achieved by performing a general exclusion.
2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.

Join the Z-Wave Network

1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
2. Depress the Tamper switch for 1 second then release. The LED on the sensor will begin flashing.
3. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevationâ„¢
4. The LED on the sensor will stop flashing
5. Watch the status in the device details page to confirm proper operation.

Exclusion the Z-Wave Network

1. From the device's details page, select Remove Device, then Remove
2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
3. Press the Tamper switch of WADWAZ-1 for 1 second and release to exclude the device form the Z-wave network.
4. The LED light will flash continuously when the sensor is in the excluded condition.

Device

Product Number

Device Type

Protocol

Door / Window Sensor

WADWAZ-1

Contact Sensor

Z-Wave

Device

Product Number

Device Type

Protocol

PIR Motion Detector

WAPIRZ-1

Motion Sensor

Z-Wave

Factory Reset

1. Factory reset is achieved by performing a general exclusion.
2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.

Join the Z-Wave Network

1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
2. Depress the Tamper switch for 1 second then release. The LED on the sensor will begin flashing.
3. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevationâ„¢
4. The LED on the sensor will stop flashing
5. Watch the status in the device details page to confirm proper operation.

Exclusion the Z-Wave Network

1. From the device's details page, select Remove Device, then Remove
2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
3. Press the Tamper switch of WAPIRZ-1 for 1 second and release to exclude the device form the Z-wave network.
4. The LED light will flash continuously when the sensor is in the excluded condition.

Device

Product Number

Device Type

Protocol

Siren / Strobe

WA105DBZ-1

Siren

Z-Wave

Factory Reset

1. Factory reset is achieved by performing a general exclusion.
2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.

Join the Z-Wave Network

1. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
2. Press the siren/strobe Program/Tamper switch for 1 second then release. The LED on the sensor will begin flashing.
3. Wait for the device to be added into the system, successful pairing will be confirmed by Hubitat Elevationâ„¢
4. The LED on the sensor will stop flashing
5. Watch the status in the device details page to confirm proper operation.

Exclusion the Z-Wave Network

1. From the device's details page, select Remove Device, then Remove
2. From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
3. Press the siren/strobe Program/Tamper switch for 1 second then release to exclude the device form the Z-wave network.
4. The LED light will flash continuously when the sensor is in the excluded condition.